当油泵与电机间联轴器损坏会报出()故障。
第1题:
Running an electric winch at slow speed over a long period of time causes ______.
A.the speed to be retarded by the friction brake
B.a load to go downward at full speed
C.the circuit breaker to turn off
D.the resistors to overheat and eventually burn out
第2题:
英译汉:gearbox
第3题:
Err131故障解释为()、Err154故障解释为()。
第4题:
英译汉:gearbox ratio
第5题:
four-stroke
two-stroke
slow speed
reversible
第6题:
runs out of fuel
has low lubricating oil pressure
exceeds a set maximum speed
has high cooling water temperature
第7题:
stand by
put up with
withhold
withstand
第8题:
The high temperature facilitates primary gravity separation
Most of the oil and organic solvents are raised to the top layer
The high the temperature is, the more the top oil will be collected
The high temperature has little use on the separation of emulsified oil
第9题:
alternator
turbo-charger
remote controller
windlass
第10题:
have a high viscosity index
mix readily with refrigerant
have a high freezing point
have a low pour point
第11题:
Excessive fuel
Higher than normal temperatures for star up
Longer starting periods
Higher than normal lube oil pressure
第12题:
第13题:
材料:
While berthed alongside in Tenerife,the cruise ship Arcadia was carrying out a lifeboat drill.One lifeboat was successfully launched and as it was being recovered,the winch hoisting it failed.The lifeboat was still connected to the falls and it dropped back into the sea. To investigate what had happened,the crew had to wind the falls back onto the winch drum.The lifeboat was disconnected while the crew tried to restart the winch.They were unsuccessful because of a fault on the hand crank cutout switch.
The crew then attempted to wind the falls back on using the hand crank,but because of the time and effort involved,the cutout switch was bypassed and power restored to speed up the operation.The crank handle was left in place. The winch was started.It began to turn and so too did the handle which hit one of the crew over the head.
The investigation found that the winch failed in the first place because the oil used in the winch gearbox was not one recommended.It was too viscose and would have prevented the coupling locking mechanism from operating correctly.
问题:
It was the fault on the ________ that caused the failure to recover the lift boat
A.crank handle
B.hand crank cutout switch
C.power system
D.falls
It was the ________ that hit the crewmember on his head.A.falls
B.hand crank cutout switch
C.crank handle
D.winch drum
The cause of the accident was that ________.A.the oil used in the winch gearbox was too viscose
B.the winch drum was connected with the falls
C.the life boat was too heavy
D.the bypass to the cutout switch was misused by the crew
The lesson from this accident is that ________.A.seafaring is not all about facing unforeseen situations
B.it is not necessary to wear hard hats to prevent sore heads
C.the wrong oil can not have serious repercussions
D.do not start lifeboat winch motors with the crank handle in place
请帮忙给出每个问题的正确答案和分析,谢谢!
第14题:
当风机报故障154“Gearbox high speed pump no pressure”都有可能是什么原因造成的?
第15题:
DSG(DireCt-Shift GeArBox)中文字面意思为()。
第16题:
supplying high pressure oil into a hydraulic motor
supplying high temperature air into the cylinder
supplying high pressure air into the cylinder
electrical igniting
第17题:
To reduce the main engine speed
To increase the main engine speed
To govern the main engine speed
To fix the propeller shaft
第18题:
excessive mist density in the crankcases
excessively high crankcase vacuum
excessively high bearing temperature
excessive carbon buildup in the lube oil
第19题:
电子燃油喷射系统
柴油高压共轨喷漆技术
直接超越齿轮箱
直接换挡变速箱
第20题:
at high speed and full load
at low speed and part load
when heavy fuel oil is used at sea
when the ships run long distance
第21题:
four-stroke
two-stroke
slow speed
reversible
第22题:
employing fuel oil as a cooling medium
preventing hard carbon deposit on nozzle tips
avoiding fuel oil temperature exceeding builder’s specification
ensuring good metallic contact between nozzles and cylinder heads
第23题: