itgle.com

单选题Which of the following is MOST critical when installing a new processor in an existing system?（）A Thermal pasteB FansC Drive speedsD Cable management

题目
单选题
Which of the following is MOST critical when installing a new processor in an existing system?（）
A

Thermal paste

B

Fans

C

Drive speeds

D

Cable management

相似考题

1.Which of the following is the MOST critical component related to removing heat from the CPU?()A. Vented caseB. Number of fansC. Thermal pasteD. Liquid cooling

2.After installing a new hard drive into a server for the purpose of mirroring the data from the first drive to the second one， the server displays an “operating system not found” error. Which of the following should the technician do to boot the server from the original drive？（）A、Replace the second drive with a hot swappable one.B、Swap the drive boot order in the BIOSC、Make the second disk active under the disk management tool.D、Rebuild the array using the hardware RAID tool at boot.

3.A new floppy drive was just installed into a PC. The drive powers on at system boot but the status LED does not turn off during operation. Which of the following is MOST likely the issue?（）A、The power cable was installed incorrectly and needs to be flipped.B、The floppy drive was not enabled within the motherboard’s BIOS.C、The FDD cable was installed incorrectly and needs to be flipped.D、A Molex power cable was used instead of a Berg cable.

4.Which of the following is MOST critical when installing a new processor in an existing system?()A. Thermal pasteB. FansC. Drive speedsD. Cable management

更多“单选题Which of the following is MOST critical when installing a new processor in an existing system?（）A Thermal pasteB FansC Drive speedsD Cable management”相关问题

  • 第1题：

    After installing the Windows operating system, Device Manager shows a number of devices with a yellow question mark next to them. Which of the following is the MOST likely reason?（）

    • A、The latest service pack needs to be installed.
    • B、The created hard drive partition is not large enough.
    • C、The motherboard chipset driver needs to be installed.
    • D、The processor does not support the Windows OS.

    正确答案:C

  • 第2题：

    Which of the following is the MOST critical component related to removing heat from the CPU?（）

    • A、Vented case
    • B、Number of fans
    • C、Thermal paste
    • D、Liquid cooling

    正确答案:C

  • 第3题：

    After installing a new SATA hard drive the technician notices the drive is hot to the touch and is giving off a slight odor. Which of the following should the technician do? （）

    • A、Install a larger fan near the hard drive to cool the system.
    • B、Clean the drive with compressed air and continue to use it.
    • C、Remove and replace the drive.
    • D、Apply more thermal compound and reseat the drive.

    正确答案:C

  • 第4题：

    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）

    • A、The new drive’s jumper is set for master.
    • B、The new drive is connected to the secondary bus as a slave drive.
    • C、Both drives’ jumpers are set for cable select.
    • D、The old drive’s jumper is set for master and the new drive is set for slave.

    正确答案:A

  • 第5题：

    An administrator reboots a ten drive server, with a RAID 10 array, after a power failure and receives an error logical drive failed. Which of the following is the MOST likely cause?（）

    • A、Corrupt file system table
    • B、Backplane failure
    • C、Multiple drive failure
    • D、Bad cable

    正确答案:B

  • 第6题：

    单选题
    A technician is performing a memory upgrade by installing an additional 1GB stick of DDR RAM into a system. When the installation is complete, the computer shows 2GB of RAM at POST; however, it now indicates a lower speed setting for the memory. Which of the following is the MOST likely cause?（）
    A

    The newly installed RAM has a lower clock speed than the existing RAM.

    B

    The CPU is not configured to work with the additional RAM.

    C

    The system is incompatible with the new RAM.

    D

    The new RAM is of lower quality, and not dependable at higher speeds.


    正确答案： D
    解析： 暂无解析

  • 第7题：

    单选题
    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）
    A

    The new drive’s jumper is set for master.

    B

    The new drive is connected to the secondary bus as a slave drive.

    C

    Both drives’ jumpers are set for cable select.

    D

    The old drive’s jumper is set for master and the new drive is set for slave.


    正确答案： A
    解析： 暂无解析

  • 第8题：

    单选题
    A client purchased a new internal hard drive to act as a second drive on a legacy machine. When the client attempts to install the drive, the cable connector on the new drive is not compatible with the available IDE cables. It is determined that the client has purchased a SATA hard drive. Which of the following would the technician recommend as the BEST solution to this situation?（）
    A

    Have the client purchase a SATA compatible system board.

    B

    Have the client purchase a SATA to IDE conversion kit.

    C

    Have the client return the drive and purchase an IDE compatible drive.

    D

    Have the client purchase a SCSI to SATA conversion kit.


    正确答案： C
    解析： 暂无解析

  • 第9题：

    单选题
    After installing the Windows operating system, Device Manager shows a number of devices with a yellow question mark next to them. Which of the following is the MOST likely reason?（）
    A

    The latest service pack needs to be installed.

    B

    The created hard drive partition is not large enough.

    C

    The motherboard chipset driver needs to be installed.

    D

    The processor does not support the Windows OS.


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）
    A

    Windows cannot be booted from a controller card.

    B

    The hard drive must have Windows reinstalled because a new controller card was installed.

    C

    The SATA controller card was not set as a boot device in the computer BIOS.

    D

    The new controller must have the correct jumper settings for Windows mode.


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    Which of the following is the MOST important consideration when purchasing a new server for a mission critical application？（）
    A

    RAID 0 compliant

    B

    Notifying all stakeholders of the server upgrade

    C

    Service Level Agreement

    D

    KVM access


    正确答案： C
    解析： 暂无解析

  • 第12题：

    单选题
    An administrator reboots a ten drive server， with a RAID 10 array， after a power failure and receives an error logical drive failed.  Which of the following is the MOST likely cause？（）
    A

     Corrupt file system table

    B

     Backplane failure

    C

     Multiple drive failure

    D

     Bad cable


    正确答案： B
    解析： 暂无解析

  • 第13题：

    A technician is performing a memory upgrade by installing an additional 1GB stick of DDR RAM into a system. When the installation is complete, the computer shows 2GB of RAM at POST; however, it now indicates a lower speed setting for the memory. Which of the following is the MOST likely cause?（）

    • A、The newly installed RAM has a lower clock speed than the existing RAM.
    • B、The CPU is not configured to work with the additional RAM.
    • C、The system is incompatible with the new RAM.
    • D、The new RAM is of lower quality, and not dependable at higher speeds.

    正确答案:A

  • 第14题：

    After a technician installs a new CMOS battery on a motherboard, which of the following will thetechnician have to change? （）

    • A、Firmware version
    • B、System date/time
    • C、Bus speeds
    • D、Jumper settings

    正确答案:B

  • 第15题：

    Which of the following is MOST critical when installing a new processor in an existing system?（）

    • A、Thermal paste
    • B、Fans
    • C、Drive speeds
    • D、Cable management

    正确答案:A

  • 第16题：

    A floppy drive is replaced in a computer and now when the computer is turned on the floppy drive light is constantly lit. Which of the following is the MOST likely cause?（）

    • A、The power supply has failed.
    • B、The drive cable is connected backwards.
    • C、The floppy drive has failed.
    • D、The proper drivers have not been loaded.

    正确答案:B

  • 第17题：

    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）

    • A、Windows cannot be booted from a controller card.
    • B、The hard drive must have Windows reinstalled because a new controller card was installed.
    • C、The SATA controller card was not set as a boot device in the computer BIOS.
    • D、The new controller must have the correct jumper settings for Windows mode.

    正确答案:C

  • 第18题：

    多选题
    When configuring a POS system, which of the following peripheral devices would MOST likelyneed to be installed?（）
    A

    Optical mouse

    B

    Handheld digitizer

    C

    Barcode reader

    D

    Touchscreen

    E

    Document scanner

    F

    Keyboard

    G

    External USB drive


    正确答案： B,D
    解析： 暂无解析

  • 第19题：

    单选题
    After installing a new SATA hard drive the technician notices the drive is hot to the touch and is giving off a slight odor. Which of the following should the technician do? （）
    A

    Install a larger fan near the hard drive to cool the system.

    B

    Clean the drive with compressed air and continue to use it.

    C

    Remove and replace the drive.

    D

    Apply more thermal compound and reseat the drive.


    正确答案： C
    解析： 暂无解析

  • 第20题：

    单选题
    After installing a new hard drive into a server for the purpose of mirroring the data from the first drive to the second one， the server displays an “operating system not found” error. Which of the following should the technician do to boot the server from the original drive？（）
    A

    Replace the second drive with a hot swappable one.

    B

    Swap the drive boot order in the BIOS

    C

    Make the second disk active under the disk management tool.

    D

    Rebuild the array using the hardware RAID tool at boot.


    正确答案： C
    解析： 暂无解析

  • 第21题：

    单选题
    Which of the following is MOST critical when installing a new processor in an existing system?（）
    A

    Thermal paste

    B

    Fans

    C

    Drive speeds

    D

    Cable management


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    After installing a new optical drive into a workstation, which of the following will ask for anacknowledgement?（）
    A

    IRQ Manager

    B

    BIOS

    C

    Device Manager

    D

    Hardware Compatibility List


    正确答案： D
    解析： 暂无解析

  • 第23题：

    单选题
    An administrator reboots a ten drive server, with a RAID 10 array, after a power failure and receives an error logical drive failed. Which of the following is the MOST likely cause?（）
    A

    Corrupt file system table

    B

    Backplane failure

    C

    Multiple drive failure

    D

    Bad cable


    正确答案： B
    解析： 暂无解析

  • 第24题：

    单选题
    A new floppy drive was just installed into a PC. The drive powers on at system boot but the status LED does not turn off during operation. Which of the following is MOST likely the issue?（）
    A

    The power cable was installed incorrectly and needs to be flipped.

    B

    The floppy drive was not enabled within the motherboard’s BIOS.

    C

    The FDD cable was installed incorrectly and needs to be flipped.

    D

    A Molex power cable was used instead of a Berg cable.


    正确答案： C
    解析： 暂无解析

相关内容