itgle.com

Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP route

题目

Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）

A. The no auto - summary command needs to be added under router eigrp 1

B. The subnets keyword was not included in the redistribute command under router ospf 1

C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A

D. The default - information originate command needs to be added under router ospf 1

E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF

相似考题

1.How can a Ezonexam administrator determine if a router has been configured when it is first powered up?A．A configured router prompts for a passwordB．A configured router goes to the privileged mode promptC．An un configured router goes into the setup dialogD．An un configured router goes to the enable mode prompt

2.Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）A. Network BB. Network A and Network BC. Network AD. neither Network A nor Network B

3.Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

4.Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP.Which of the following answers lists an item that cannot be matched by route map fred?（）A. Subnet numberB. Next - hop router IP address of the routeC. Whether the route is an E1 or E2 routeD. The ro ute‘s tagE. The number of router hops between the router and the subnet

更多“Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual ”相关问题

  • 第1题：

    Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）

    A. Redistribute connected interfaces on router B and router C

    B. Set the maximum nu mber of equal cost paths to1 in all routers

    C. When redistributing EIGRP into OSPF, set the external metric type to type E1

    D. Adjust the default metrics in router B and router C so that the values are different in each router

    E. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol


    参考答案：E

  • 第2题：

    Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）

    A. Declare router B a stub router using the eigrp stub command.

    B. Use the passive - interface command for interface Serial0/0/0.

    C. Use a mask with the network command to exclude interface Serial0/0/0.

    D. Implement a distribute list to exclude the link prefix from the routi ng updates.


    参考答案：C

  • 第3题：

    Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? ()

    A. Router A will prefer the path through router B for network 172.20.0.0

    B. Router A will prefer the path through router C for network 172.20.0.0

    C. Packets from router D will prefer the path through router B for networks advertised by router A

    D. Packets from r outer D will prefer the path through router C for networks advertised by router A


    参考答案：A

  • 第4题：

    Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?()

    A. The no auto - summary command has not been issued under the EIGRP process on both routers.

    B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.

    C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.

    D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.


    参考答案：D

  • 第5题：

    Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）

    A.Check and change the access lists on router RTA

    B.Configure the auto summary command under router eigrp 1 on router RTA

    C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface

    D.Issue the no ip split horizon command on router RTA

    E.Issue the no ip split horizon eigrp 1 command on router RTA

    F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers


    参考答案：E

  • 第6题：

    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

    • A、As numbers must be changed to match on all the routers.
    • B、Loopback interface must be configured so a DR is elected.
    • C、The no auto-summary command is needed on Router A and Router C.
    • D、Router B needs to have two network statements, one for each connected network.

    正确答案:A

  • 第7题：

    Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）

    • A、Subnet number
    • B、Next - hop router IP address of the route
    • C、Whether the route is an E1 or E2 route
    • D、The ro ute's tag
    • E、The number of router hops between the router and the subnet

    正确答案:E

  • 第8题：

    A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）

    • A、172.16.0.1/23
    • B、172.16.1.1/26
    • C、172.16.1.1/24
    • D、172 .16.0.255/23
    • E、None of the other answers is correct.

    正确答案:B,C

  • 第9题：

    单选题
    Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?（）
    A

    10.1.1.2

    B

    10.154.154.1

    C

    172.16.5.1

    D

    192.168.5.3


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configuration statement should be included on router R4 to advertise a default route to its neighbors？（）
    A

    R4（config）# ip default-network 10.0.0.0

    B

    R4（config）# ip route 0.0.0.0 0.0.0.0 10.1.1.1

    C

    R4（config）# ip route 10.0.0.0 255.0.0.0 10.1.1.1

    D

    R4（config-router）# default-information originate


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    How can an administrator determine if a router has been configured when it is first powered up?（）
    A

    A configured router prompts for a password

    B

    A configured router goes to the privileged mode prompt

    C

    An un configured router goes into the setup dialog

    D

    An un configured router goes to the enable mode prompt


    正确答案： C
    解析： 暂无解析

  • 第12题：

    单选题
    Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）
    A

    Subnet number

    B

    Next - hop router IP address of the route

    C

    Whether the route is an E1 or E2 route

    D

    The ro ute's tag

    E

    The number of router hops between the router and the subnet


    正确答案： A
    解析： 暂无解析

  • 第13题：

    Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

    A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

    B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

    C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

    D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253


    参考答案：A, B, D

  • 第14题：

    Refer to the exhibit. Which th ree commands should be used on router B1 to redistribute the EIGRP AS 10 routes into RIP?()

    A. router rip

    B. router eigrp 10

    C. redistribute eigrp 10

    D. redistribute rip

    E. default - metric 10000 100 255 1 1500

    F. default - metric 5


    参考答案：A, C, F

  • 第15题：

    Refer to the exhibit. Which st atement is true?()

    A. Router RTA is the BDR

    B. Router RTA is directly connected to interface 192.168.45.1

    C. Neighbor 192.168.45.1 has changed its OSPF priority number

    D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs


    参考答案：A

  • 第16题：

    Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3?（）

    A. 10.0.0.0/8

    B. 172.16.10.0/24

    C. 172.16.0.0/24

    D. 10.10.10.0/24

    E. 172.16.0.0/16

    F. 10.10.0.0/16


    参考答案：D, E

  • 第17题：

    Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?()

    A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1

    B. R4(config)# ip default - network 10.0.0.0

    C. R4(config - router)# default -information originate

    D. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1


    参考答案：B

  • 第18题：

    Refer to the exhibit. Which statement is correct based on the show login command output shown？（）

    • A、When the router goes into quiet mode， any host is permitted to access the router via Telnet，SSH， and HTTP，since the quiet-mode access list has not been configured.
    • B、The login block-for command is configured to block login hosts for 93 seconds.
    • C、All logins from any sources are blocked for another 193 seconds.
    • D、Three or more login requests have failed within the last 100 seconds.

    正确答案:D

  • 第19题：

    How can an administrator determine if a router has been configured when it is first powered up?（）

    • A、A configured router prompts for a password
    • B、A configured router goes to the privileged mode prompt
    • C、An un configured router goes into the setup dialog
    • D、An un configured router goes to the enable mode prompt

    正确答案:C

  • 第20题：

    Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）

    • A、R1 has been configured with an ip default- network 2.0.0.0 command.
    • B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.
    • C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
    • D、Another router has been configured with an ip default - network 2.0.0.0 command.
    • E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.

    正确答案:D

  • 第21题：

    单选题
    Refer to the exhibit. Which statement is correct based on the show login command output shown？（）
    A

    When the router goes into quiet mode， any host is permitted to access the router via Telnet，SSH， and HTTP，since the quiet-mode access list has not been configured.

    B

    The login block-for command is configured to block login hosts for 93 seconds.

    C

    All logins from any sources are blocked for another 193 seconds.

    D

    Three or more login requests have failed within the last 100 seconds.


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）
    A

    As numbers must be changed to match on all the routers.

    B

    Loopback interface must be configured so a DR is elected.

    C

    The no auto-summary command is needed on Router A and Router C.

    D

    Router B needs to have two network statements, one for each connected network.


    正确答案： B
    解析： 暂无解析

  • 第23题：

    单选题
    Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）
    A

    R1 has been configured with an ip default- network 2.0.0.0 command.

    B

    R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.

    C

    R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.

    D

    Another router has been configured with an ip default - network 2.0.0.0 command.

    E

    Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.


    正确答案： A
    解析： 暂无解析

相关内容