itgle.com

Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()A. Issue the command bandwidth 224 on the physical interface.B. Issue the command bandwidth 56 on the physical interface

题目
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()

A. Issue the command bandwidth 224 on the physical interface.

B. Issue the command bandwidth 56 on the physical interface.

C. Issue the command bandwidth 224 on each subinterface.

D. Issue the command bandwidth 56 on each subinterface.

相似考题

1.Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface.What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）A. ip ospf network broadcastB. ip ospf network non - broadcastC. ip ospf network point - to - multipointD. ip ospf network point - to - multipoint non - broadcast

2.Refer to the exhibit. Which th ree commands should be used on router B1 to redistribute the EIGRP AS 10 routes into RIP?()A. router ripB. router eigrp 10C. redistribute eigrp 10D. redistribute ripE. default - metric 10000 100 255 1 1500F. default - metric 5

3.Refer to the above exhibit. Why are the EIGRP neighbors for this router not learning the routes redistributed from OSPF?()A. Redistribution must be enabled mutually (in both directions) to work correctly.B. auto - summary causes the OSPF routes redistributed into EIGRP to be summarized; thus the OSPF network 116.16.34 is summarized to 116.3 4.0.0, which is already covered by the EIGRP protocol.C. Default metrics are not configured under EIGRP.D. Both routing protocols must have unique autonomous system numbers for redistribution to function correctly.

4.Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF

更多“Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?() ”相关问题

  • 第1题：

    Refer to the exhibit. You are the network administrator of the Route.com company. You have been tasked to implement a hub and spoke EIGRP topology over Frame Relay to provide connectivity between the networks at headquarters and all 300 spokes. Before you begin the actual implementation, which three pieces of information are more important to know than the others?（）

    A. the Committed Information Rate of all the Frame Relay PVCs

    B. the Cisco IOS version running on all the routers

    C. the router model number of all the spoke routers

    D. the number of HQ networks connected behind the headquarter routers

    E. the routing policy, such as whether or not the spokes can be used as backup transient point between the two headquarter routers


    参考答案：A, B, E

  • 第2题：

    Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）

    A.Check and change the access lists on router RTA

    B.Configure the auto summary command under router eigrp 1 on router RTA

    C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface

    D.Issue the no ip split horizon command on router RTA

    E.Issue the no ip split horizon eigrp 1 command on router RTA

    F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers


    参考答案：E

  • 第3题：

    A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）

    • A、Router(config-if)# encapsulation frame-relay q933a
    • B、Router(config-if)# encapsulation frame-relay ansi
    • C、Router(config-if)# encapsulation frame-relay ietf
    • D、Router(config-if)# encapsulation frame-relay isl
    • E、None of the above

    正确答案:C

  • 第4题：

    EIGRP has been configured to operate over Frame Relay multipoint connections. What should the bandwidth command be set to?（）

    • A、the CIR rate of the lowest speed connection multiplied by the num ber of circuits
    • B、the CIR rate of the lowest speed connection
    • C、the CIR rate of the highest speed connection
    • D、the sum of all the CIRs divided by the number of connections

    正确答案:A

  • 第5题：

    EIGRP has been configured to opera te over Frame Relay multipoint connections. What should the bandwidth command be set to?（）

    • A、the CIR rate of the lowest speed connection multiplied by the number of circuits
    • B、the CIR rate of the lowest speed connection
    • C、the CIR rate of the highest s peed connection
    • D、the sum of all the CIRs divided by the number of connections

    正确答案:A

  • 第6题：

    Which three statements about L2TPv3 are true？（）

    • A、L2TPv3 Frame Relay support includes only 32-bit DLCI addressing
    • B、L2TPv3 sessions do not support Frame Relay LMI interworking
    • C、Multipoint DLCI is not supported
    • D、To use DCE or a Network-to-Network Interface on a Frame Relay port， you must configure the frame-relay switching command
    • E、L2TPv3 feature does not support Frame Relay extended addressing

    正确答案:B,D,E

  • 第7题：

    A default Frame Relay WAN is classified as what type of physical network？（）

    • A、point-to-point
    • B、broadcast multi-access
    • C、nonbroadcast multi-access
    • D、nonbroadcast multipoint.broadcast point-to-multipoint

    正确答案:C

  • 第8题：

    Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）

    • A、ip ospf network broadcast
    • B、ip ospf network non - broadcast
    • C、ip ospf network point - to - multipoint
    • D、ip ospf network point - to - multipoint non - broadcast

    正确答案:C

  • 第9题：

    单选题
    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）
    A

    As numbers must be changed to match on all the routers.

    B

    Loopback interface must be configured so a DR is elected.

    C

    The no auto-summary command is needed on Router A and Router C.

    D

    Router B needs to have two network statements, one for each connected network.


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）
    A

    The IP addresses are configured incorrectly.

    B

    Frame Relay LMI messages not displayed in real time.

    C

    The administrator must issue the enable frame-relay lmi debug command.

    D

    The administrator must issue the terminal monitor command.

    E

    Debug messages can only be received once through the console port.

    F

    The administrator must issue the show frame-relay lmi vty 0 4 command


    正确答案： C
    解析： 暂无解析

  • 第11题：

    单选题
    Which of the following is true concerning Frame Relay multipoint subinterfaces?（）
    A

    An IP address is required on the physical interface of the central router.

    B

    All routers are required to be fully meshed.

    C

    All routers must be in the same subnet to forward routing updates and broadcasts.

    D

    Multipoint is the default configuration for Frame Relay subinterfaces.


    正确答案： C
    解析： 暂无解析

  • 第12题：

    单选题
    A default Frame Relay WAN is classified as what type of physical network?（）
    A

    point-to-point  

    B

    broadcast multi-access  

    C

    nonbroadcast multi-access  

    D

    nonbroadcast multipoint 

    E

    broadcast point-to-multipoint 


    正确答案： E
    解析： 暂无解析

  • 第13题：

    Refer to the exhibit. Which st atement is true?()

    A. Router RTA is the BDR

    B. Router RTA is directly connected to interface 192.168.45.1

    C. Neighbor 192.168.45.1 has changed its OSPF priority number

    D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs


    参考答案：A

  • 第14题：

    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

    • A、As numbers must be changed to match on all the routers.
    • B、Loopback interface must be configured so a DR is elected.
    • C、The no auto-summary command is needed on Router A and Router C.
    • D、Router B needs to have two network statements, one for each connected network.

    正确答案:A

  • 第15题：

    In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）

    • A、The IP addresses are configured incorrectly.
    • B、Frame Relay LMI messages not displayed in real time.
    • C、The administrator must issue the enable frame-relay lmi debug command.
    • D、The administrator must issue the terminal monitor command.
    • E、Debug messages can only be received once through the console port.
    • F、The administrator must issue the show frame-relay lmi vty 0 4 command

    正确答案:D

  • 第16题：

    Which of the following is true concerning Frame Relay multipoint subinterfaces?（）

    • A、An IP address is required on the physical interface of the central router.
    • B、All routers are required to be fully meshed.
    • C、All routers must be in the same subnet to forward routing updates and broadcasts.
    • D、Multipoint is the default configuration for Frame Relay subinterfaces.

    正确答案:C

  • 第17题：

    The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）

    • A、The Gallant router has the wrong LMI type configured
    • B、Inverse ARP is providing the wrong PVC information to the Gallant router
    • C、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
    • D、The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
    • E、The IP address on the serial interface of the Attalla router is configured incorrectly

    正确答案:D

  • 第18题：

    Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）

    • A、 Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.
    • B、 This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.
    • C、 The router at RemoteB must be replaced by a Cisco router.
    • D、 Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.
    • E、 There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.

    正确答案:D

  • 第19题：

    在配EIGRP的时候（frame-relay的NBMA）命令router（config-router）#neighbor 192.168.1.129 是什么意思呢？


    正确答案:specify a neighbor router to establish EIGRP peer with via unicast.

  • 第20题：

    单选题
    Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR and require static OSPF neighbor definition?（）
    A

    ip ospf network broadcast

    B

    ip ospf netw ork non - broadcast

    C

    ip ospf network point - to - multipoint

    D

    ip ospf network point - to - multipoint non - broadcast


    正确答案： A
    解析： 暂无解析

  • 第21题：

    问答题
    在配EIGRP的时候（frame-relay的NBMA）命令router（config-router）#neighbor 192.168.1.129 是什么意思呢？

    正确答案： specify a neighbor router to establish EIGRP peer with via unicast.
    解析： 暂无解析

  • 第22题：

    单选题
    EIGRP has been configured to operate over Frame Relay multipoint connections. What should the bandwidth command be set to?（）
    A

    the CIR rate of the lowest speed connection multiplied by the num ber of circuits

    B

    the CIR rate of the lowest speed connection

    C

    the CIR rate of the highest speed connection

    D

    the sum of all the CIRs divided by the number of connections


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）
    A

     Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.

    B

     This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.

    C

     The router at RemoteB must be replaced by a Cisco router.

    D

     Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.

    E

     There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.


    正确答案： D
    解析： 暂无解析

相关内容